Where to buy high-quality aluminum pedal covers for EQE?

Not to disagree, but honestly I've had a different experience with the floor-mounted setup. Everyone says you gotta go aftermarket for that "AMG look," but i tried a few cheap sets and the fitment was just sketchy, you know? I actually ended up just swapping the whole pedal assemblies for the performance ones found in higher trims. It was way more work than a slip-on cover, but the tactile feel is actually SOLID and nothing slides around. If you're picky about quality, id consider just doing the full swap instead of covers.

Basically, I went through this exact same thing cuz the stock plastic ones look so cheap in an expensive EV... it's kinda annoying tbh. Before you buy anything, you gotta understand that the EQE uses a specific floor-mounted hinge, so most generic sets won't work at all. For your situation, I would suggest looking into the Mercedes-Benz Genuine AMG Stainless Steel Pedal Covers for EQE V295. I know the price is high, but the fitment is LITERALLY perfect since they're OEM.

I actually tried some cheap ones first and they were super sketchy... like, they moved around when I braked hard. Not good. If you want a cheaper but still high-quality alternative, check out the Shaohao Aluminum Alloy Non-Slip Pedal Covers for Mercedes EQE. Installation is a bit of a workout tho!! The brake pedal is a simple swap, but that accelerator cover takes some serious prying to get the rubber lips to wrap around the back. Pro tip: soak the rubber in hot water for a few mins first to make it soft. It makes it wayyy easier to stretch over. gl with the upgrade!

For your situation, I would suggest looking at V-Tuning Aluminum Alloy Nonslip Pedal Set for Mercedes-Benz EQE. They're wayyy cheaper than OEM but the quality is actually solid.

1. Stick to the ones with the thick rubber studs for grip—really important in the rain!!
2. Make sure it's for the V295 floor-mount specifically.
3. Pro tip: soak the rubber in hot water before installing. Makes it sooo much easier to stretch over the pedals. gl!

Seconding the recommendation above regarding those rubber studs! Honestly, safety is the biggest deal here because aluminum gets *slick* when your shoes are wet. I totally agree that the floor-mounted accelerator in the EQE makes fitment tricky, so you really gotta be careful.

Since you're looking for high-end technical specs and want to avoid the ones already mentioned, I'd suggest looking into the Kies Motorsports Aluminum Pedal Set for Mercedes-Benz or the Dewhel Anti-Slip Aluminum Pedal Covers for Mercedes EQE V295. Both use a high-friction TPE rubber backing that actually wraps around the pedal plate rather than just clipping on, which is CRITICAL for that snug, no-slide feel you're after.

From a technical perspective, you've got three main types:
1. **Clip-ons:** Basically junk. They vibrate and can actually slip off under heavy braking.
2. **Slip-over/Wrap-around:** These are the sweet spot. They replace the factory rubber pads and use the lip of the pedal to stay secure.
3. **Full Assembly Replacement:** The OEM route. It's the most secure but also way more work and expensive.

Anyway, if you go with the Dewhel Anti-Slip Aluminum Pedal Covers, just a pro-tip: soak the rubber backings in hot water for like 5 minutes before installing. It makes the material way more pliable so you can get that tight seal over the metal edges without breaking a sweat. It's a bit of a thumb-buster otherwise, but once they're on, they don't budge. Good luck with the upgrade!! 👍

My buddy told me the exact same thing last week. Guess he was right lol.

Huh interesting. I had no idea. The more you know I guess 🤷

I've been down this rabbit hole too and you really gotta be careful with the fitment on that floor-mounted gas pedal. Id suggest checking out a couple of others that havent been mentioned yet:

• D-Lumina Aluminum Alloy Anti-Slip Pedal Covers for Mercedes EQE
• Pros: These are built like tanks and the rubber inserts are actually quite grippy. Cons: Watch out during the install cuz the rubber is stiff as a board... youll probably need a hairdryer to soften it up or youll lose a fingernail.
• CDEFG Sport Gas and Brake Pedal Covers for Mercedes EQE
• Pros: These look very sleek and match the interior trim almost perfectly. Cons: The metal isnt quite as thick as some others, so id be a bit wary of how they hold up over a few years of heavy use. Make sure whatever you pick has a really deep lip on the back so it wont pop off while youre driving. That happened to a buddy of mine in his old C-class and it was sketchy as hell. Actually, speaking of interior stuff, I just noticed the other day how much the piano black trim on the center console scratches if you even breathe on it. Spent all weekend looking at PPF kits for the interior... anyway, its a rabbit hole once you start modding the cabin. But yeah, watch those rubber tabs on the install.

Can confirm