Top recommended bed accessories for the new Ford Maverick?

For your situation, i've had both and the BakFlip MX4 Hard Folding Tonneau Cover is way better for security vs a soft roll-up... but it's pricey. For the bed: - Spray-in: Best protection, no sliding.
- Dee Zee Heavy Duty Bed Mat: Cheap, easy to clean. I'd definately suggest a Line-X Spray-In Bedliner. Mats can trap moisture and scratch paint... anyway, gl with the truck!

Hmm, I've had a different experience when it comes to prioritizing just security or cost. Everyone loves those hard covers, but from a safety-first perspective, they literally block ur entire rear window when they’re folded up. If youre hauling a tall load from the hardware store, thats a huge blind spot and pretty dangerous in traffic. Instead of the usual suspects mentioned, I'd actually suggest the TruXedo Lo Pro Soft Roll Up Truck Bed Tonneau Cover 553101. It rolls up into a tiny bundle at the bulkhead, keeping your sightlines clear, which is honestly way safer for highway driving. Also, for the bed surface, I think people sleep on the BedRug Classic Bed Liner BRF22MAV. It protects ur knees when crawling in that small 4.5ft bed and stops camping gear from sliding around way better than a rubber mat. For those DIY Flexbed slots:
- Use pressure-treated lumber so it doesn't rot after one rainy weekend.
- Grab some Bull Ring 4001-XT Flush Fit Retractable Tie Down Anchors to add more points for straps since the stock ones are limited.
- Always keep a set of Rhino USA Heavy Duty Ratchet Tie Down Straps 1828lb Break Strength in the side cubby. Basically, focus on how youre gonna secure the actual cargo. A secure bed cover is great, but a secure *load* is what keeps you and everyone else safe on the road. tbh security is overrated if you cant see whats behind you! gl with the build 👍

Been using this for years, no complaints

So basically the consensus is that the BakFlip is king for security and a mat is the way to go. If you wanna save more cash: * Try the Tyger Auto T1 Soft Roll-up Truck Bed Tonneau Cover TG-BC1F9061
* Just use 2x4s for those Flexbed slots! In my experience, those DIY dividers are reallyyy helpful for hardware runs. Tbh, you dont need the expensive accessories to start out! gl!

I've had my Mav since the first wave, and honestly, you don't need to spend a fortune to make that bed work for you. Everyone talks about covers, but if you're doing camping and hardware runs, the best budget move is a hitch-mounted extender. I use the MaxxHaul 70231 Hitch Mount Bed Extender for those 8ft lumber runs and it's way more versatile than a permanent cage. For the bare metal issue, I actually went the super cheap route and used a thick horse stall mat from a farm supply store—just cut it with a utility knife to fit. It's indestructible and costs way less than the brand-name liners. Also, for the Flexbed, don't just stop at dividers! I used 2x6s in those slots to build a platform that sits flush with the wheel wells. That way, you can slide your heavy tools underneath and keep your camping gear clean on top. It basically doubles your floor space, you know? One last thing, grab a set of OxyLED Motion Sensor Closet Lights and stick them under the bed rails. They're battery powered and way cheaper than the official lighting kit... plus no wiring required!!! It's all about that DIY life with this truck, right?

Any updates on this?

Bump - same question here

Ngl, reading through this reminds me so much of my neighbor’s situation when he first got into customizing his rig. He was so excited to get everything dialed in, but he ended up ordering a bunch of stuff that supposedly fit his specific year and trim, only to find out the mounting brackets were off by just enough to make them useless. He spent weeks back and forth with customer service, and at one point, his driveway looked like a warehouse because of all the mismatched parts. It was a complete nightmare trying to see if one accessory would actually clear another once the tailgate was shut. Just seeing him struggle with those tolerances made me realize how tricky it can be when you start mixing and matching different brands... poor guy basically gave up and left the bed empty for six months out of pure annoyance. It just turned into this massive ordeal where nothing quite lined up like the photos in the catalogs promised.

I've been messing around with the Flexbed slots lately and honestly, you gotta be careful with those DIY 2x4 dividers. Recently I thought I was being smart by just dropping some wood in there to keep my camping bins from sliding, but I learned the hard way that if they aren't a snug fit, they rattle like crazy. One time I took a sharp turn and the whole divider flipped over because I didn't secure it properly. It's a cheap fix but it can be a safety hazard if your gear starts shifting while you're on the highway. Another thing to watch out for is that the bare metal bed gets incredibly hot in the sun. Actually singed my hand trying to load some mulch last week... pretty embarrassing tbh. Watch where you put your hands if you're gonna go without a liner for a bit. It's easy to overlook the small stuff when you're just getting used to the rig.

Big if true